MATERIAL RESOURCES

LABORATORY OF CEMENT SLURRY SOLUTIONS
HIGH PRESSURE AND TEMPERATURE CONSISTOMETER FANN 422
Designed to measure the consistency of grouting solutions at high pressures (up to 152 MPA) and temperatures (204°C)
HTHP AUTOCLAVE MODEL 75C-8
Designed to withstand cement stone samples at high pressures and temperatures for subsequent testing of samples for flexural and compressive strength in accordance with ISO-10426, API Spec 10A and API RP 10B standards
AUTOMATIC DEVICE VIKA E044N (MATEST)
Designed to determine the initial and final setting time of cement dough with the ability to program test cycles in accordance with ISO 10426-1-2000 and ISO 10426-2-2003 standards
WATER RECOVERY INSTRUMENT (FANN 101533370)
It is designed to determine the static water yield of cement and drilling fluids, hydraulic fracturing fluids under elevated thermobaric conditions in accordance with the standards GOST 33213-2014 (ISO 10414-1: 2008), GOST 33697-2015 (ISO 10414-2:2011), GOST 26798.1-96, ISO-10426, API Spec 10A and API RP 10B
BROOKFIELD VISCOMETER DV2T
The functional rotary viscometer is designed to measure the viscosity (in the range from 1 to 6000000 MPa * s) and the shear stress of liquids in the speed range from 0.1 to 200 rpm in accordance with the standards GOST R 56946-2016 (ISO 13500: 2008) and GOST 33565-2015
FAN 705 ES ROLLER FURNACE
Fann roller furnaces provide maturation (thermal aging) of solution samples for further analysis. High-temperature aging cells are placed inside the furnace chamber, where they are heated and rotated (agitated) on drive rollers. Samples can also be heated without rotation (static maturation)
HIGH PRESSURE AND TEMPERATURE FILTER PRESS FANN 175
The 175 ml filter press is designed to determine the filtration properties of drilling fluids and cement mixtures for research at high pressure and temperature. The pressure is up to 14 MPa in one cell and the back pressure is 6 MPa in the receiving chamber. Maximum operating temperature 177 ° C, filtration area 22.6 cm2
TEST PRESS CONTROLS DIGIMAX 3
These units are designed for testing cement samples for compression or compression and bending. Simultaneous display of load, specific load, actual load, and load schedule over time. Display of load speed (e.g. N / s) or voltage value (e.g. Mpa/s), data and graph Calibration curve with a large number of coefficients
LABORATORY OF DRILLING AND PROCESS FLUIDS
LINEAR SWELLING TESTER (LSM) MODEL 2100
Designed to determine the hydrogenation or dehydrogenation of clay shale by measuring the increase or decrease over time in the length of the reconstructed or solid core of clay shale, in accordance with GOST 33696-2015 (ISO 10416: 2008)
FANN 35 ROTARY VISCOMETER
It is designed to determine the viscosity of the drilling fluid, the value of the shear stress, allows you to observe the time-dependent characteristics of the viscosity, to make relatively accurate measurements on a non-Newtonian fluid.

The viscosity can be determined at rotation speeds of 600, 300, 200, 100, 6 and 3 rpm
OFITE HPHT VISCOMETER
The fully automated system is designed to determine the rheological properties of hydraulic fracturing fluids, drilling fluids, and grouting cements at elevated temperatures and pressures.

Technical specifications:

• Pressure up to 17237 kPa (2500 PSI). The pressure creation medium is nitrogen gas.
• Temperature up to 260°C (500°F)
OFITE HPHT DYNAMIC FILTER PRESS
The filter press measures the volume of filtration and the characteristics of crust formation in various downhole conditions. The motor-driven shaft, equipped with a propeller, rotates at different speeds inside a standard 500 ml HTTP cell.

The speed settings from 1 to 3600 rpm allow for laminar or turbulent fluid flow within the cell. By changing the length of the shaft, you can increase or decrease the shear stress
LPT 4-SEAT FILTER PRESS (FANN)
The Finn filter press is used to determine the filtration properties of drilling fluids and cement mixtures. Thanks to its operation in low pressure ranges, the filter press is one of the most effective measuring instruments in this field.

Maximum operating pressure up to 0.69 MPa (100 psi)
EASYDROP EDGE ANGLE AND SURFACE/ INTERFACIAL TENSION MEASURING DEVICE
It is designed to measure the wetting edge angle and the surface (interfacial) tension, as well as to calculate the free energy of the surface.

• Measuring range 1-180 oC
• Lens – 6x magnification
• Maximum sample size 300x50 mm
INSTALLING THE EP/LUBRICITY TESTER FANN
Designed to determine the lubricating properties of drilling fluids: measuring the fluid resistance (nature of the lubricant) between two moving surfaces is also used to determine extreme pressure properties
LEVER SCALE IN A FANN CASE
Designed to determine the absolute density of a solution sample. The main advantage of the new model 140 is that the temperature of the drilling fluid does not affect the accuracy of the readings.

Measurement limits of the device 0.72-2.88 g / cm3
Do you have any questions or would you like to become a part of our team?
Leave your question and contact information in the form below and representatives of the Scientific Center "Arctic" will contact you shortly
By clicking on the button, you consent to the processing of your personal data
Do you have any questions or would you like to become a part of our team?
Leave your question and contact information in the form below and representatives of the Scientific Center "Arctic" will contact you shortly
By clicking on the button, you consent to the processing of your personal data
© 2021 Scientific Center "Arctic"
SCIENTIFIC CENTER "ARCTIC"
The area and subject of the research center "Arctic" is the organization of scientific research to improve environmental safety and efficiency of development of existing fields, as well as the introduction of innovative approaches to new fields.
MAIN SECTIONS
CONTACT INFORMATION
Adress: 199106, Russia, 21st line V.O., 2
Saint Petersburg
Telephone: +7 (812) 328-81-75